systemdのserviceタイプ一覧を表示する方法 †systemdのservice一覧を確認するコマンドを以下に記します。 関連記事 †
serviceタイプ一覧を表示 †すべてのサービスタイプ一覧を表示するには以下のコマンドを実行します。 systemctl list-unit-files -t service 上記コマンドの実行結果例を記します。 $ systemctl list-unit-files -t service UNIT FILE STATE abrt-ccpp.service enabled abrt-oops.service enabled abrt-pstoreoops.service disabled abrt-vmcore.service enabled abrt-xorg.service enabled abrtd.service enabled accounts-daemon.service enabled alsa-restore.service static alsa-state.service static alsa-store.service static anaconda-direct.service static anaconda-nm-config.service static anaconda-noshell.service static <snip> device unitの一覧表示 †device unitの一覧表示をする場合は以下のコマンドを実行します。 systemctl list-units -t device -l 上記コマンドの実行結果例を記します。 $ systemctl list-units -t device -l UNIT sys-devices-pci0000:00-0000:00:01.1-ata3-host2-target2:0:0-2:0:0:0-block-sr0.dev sys-devices-pci0000:00-0000:00:03.0-net-enp0s3.device sys-devices-pci0000:00-0000:00:08.0-net-enp0s8.device sys-devices-pci0000:00-0000:00:0d.0-ata1-host0-target0:0:0-0:0:0:0-block-sda-sda sys-devices-pci0000:00-0000:00:0d.0-ata1-host0-target0:0:0-0:0:0:0-block-sda-sda sys-devices-pci0000:00-0000:00:0d.0-ata1-host0-target0:0:0-0:0:0:0-block-sda.dev sys-devices-platform-serial8250-tty-ttyS0.device sys-devices-platform-serial8250-tty-ttyS1.device sys-devices-platform-serial8250-tty-ttyS2.device sys-devices-platform-serial8250-tty-ttyS3.device sys-devices-virtual-block-dm\x2d0.device sys-devices-virtual-block-dm\x2d1.device <snip> mount unitの一覧表示 †mount unitの一覧表示をする場合は以下のコマンドを実行します。 systemctl list-units -t mount 上記コマンドの実行結果例を記します。 $ systemctl list-units -t mount UNIT LOAD ACTIVE SUB DESCRIPTION -.mount loaded active mounted / boot.mount loaded active mounted /boot dev-hugepages.mount loaded active mounted Huge Pages File System dev-mqueue.mount loaded active mounted POSIX Message Queue File Syst proc-fs-nfsd.mount loaded active mounted NFSD configuration filesystem sys-kernel-config.mount loaded active mounted Configuration File System sys-kernel-debug.mount loaded active mounted Debug File System var-lib-nfs-rpc_pipefs.mount loaded active mounted RPC Pipe File System <snip> swap unitの一覧表示をする場合は以下のコマンドを実行します。 †systemctl list-units -t swap 上記コマンドの実行結果例を記します。 $ systemctl list-units -t swap UNIT LOAD ACTIVE SUB DESCRIPTION dev-dm\x2d0.swap loaded active active /dev/dm-0 LOAD = Reflects whether the unit definition was properly loaded. ACTIVE = The high-level unit activation state, i.e. generalization of SUB. SUB = The low-level unit activation state, values depend on unit type. 1 loaded units listed. Pass --all to see loaded but inactive units, too. To show all installed unit files use 'systemctl list-unit-files'. 以上、systemdのservice unit一覧を確認する方法でした。 |